Follow @kepco_careers
Advanced Search
Kepco Power Solutions

For a breakdown of Kepco's modular and instrument power supplies by parameter,
please refer to the Product Selection Guide

Full Rack (200W and Half Rack (40W) Series BHK-MG Power Supplies photoBHK-MG High voltage (0-300V, 0-500V, 0-1000V, 0-2000V, linear, voltage-current stabilizers with rectangular (automatic crossover) output characteristic.
  • Two sizes: half-rack 40 watts, full-rack 200 watts.
  • FET output stage.
  • Conventional filtering or fast response.
  • Fast analog programming mode.
  • Rapid recovery current mode in fast mode.
  • Local control from panel-mounted keypad.
  • Built-in GPIB, IEEE 488.2, 12 bits.
  • Built-in RS 232 (except BHK 300-0.8MG; contact Kepco if this feature required)
  • Support for SCPI language.
  • 2-line 16 character LCD display.
  • Full read back of voltage and current on the bus.
  • Increased resolution and accuracy (x10) for reading small current.
  • Versatile output on/off port (40 watt model).
  • Extensive Protection circuitry
Link to associated quotation pageCE Logo
BOP-HV (High Voltage) Series Power Supply PhotoSERIES BOP-HV Bipolar d-c power, up to 500V or 1000V, 40 Watts.
  • Linear 4-quadrant operation.
  • FET output stage.
  • Preamplifiers for summing and scaling arbitrary input signals.
  • Wide bandwidth.
  • Voltage and current stabilization with automatic crossover to current and voltage limits.
  • Remote programming of voltage, current or both channels by external analog volage.
  • Kepco's SN 488 Digital Programmer facilitates digital programming via GPIB interface.
Link to associated quotation page CE Logo UL LISTED MARK
BOP 100W, 200W, 400W Power Supply PhotoBOP 100W, 200W, 400W Bipolar linear power supplies
  • NEW flag (200W, 400W only) Option to drive magnets up to 1 Henry
  • NEW flag (200W, 400W only) Option to drive capacitive loads up to 10mF
  • Input: Wide range input: 85-265V a-c/120-370V d-c
  • Source & sink, 4 quadrant operation.
  • Separate Voltage and Current control circuits
  • Auto crossover to Voltage and Current limits
  • Also replicates arbitrary a-c waveforms
  • Optional GPIB or RS232
  • NEW flagOptional ethernet control either through a web page or by using SCPI commands via Telnet.
  • Voltage/Current stabilizer
  • See feature details
Link to associated quotation page CE Logo UL LISTED MARK
1KW High Power BOP Power Supply PhotoBOP-MG 1000W Bipolar power supplies, programmable V/C stabilizers
  • Source & sink, 4 quadrant operation
  • Energy recuperation
  • Digital programming
  • Fast analog programming
  • Precision stabilization:
    • 0.001% source
    • 0.002% load
  • Built-in arbitrary waveform generator.
  • See complete list of features
Link to associated quotation page CE Logo UL LISTED MARK
KLP Power Supply PhotoSERIES KLP Voltage, current and power-limited operating boundaries, 1200 Watts, from 0 - 10V to 0 - 600V
  • GPIB & isolated analog controls standard on all models.
  • LAN (LXI) control optional, replaces standard RS 232 interface.
  • VXI plug&play, LabView and IVI-COM drivers.
  • Control via web browser using LAN interface.
  • True 1U height - full power operation with no spacing between units.
  • Wide range a-c input with active PFC.
Link to associated quotation pageCE Logo
KLR Power SupplySERIES KLR Automatic crossover, 1U high, 2400-watt voltage/current stabilizers, from 0 - 20V to 0 - 300V
  • Rectangular output
  • GPIB and RS 232 standard
  • Optional: GPIB and LAN for control via web browser
  • External analog programmable
  • Input 200-240V a-c
  • 19 in. x 1U
  • RODC circuit (Option R) rapidly discharges output capacitance, significantly reducing response time to reductions in output voltage.
  • Wide range a-c input with active PFC.
Link to associated quotation pageCE Logo
ATE Series Power Supplies with Digital Meters PhotoSERIES ATE-DMG Linear low-noise power supplies from 0 - 6V to 0 - 150V. Respond very quickly and precisely to voltage and current setting instructions from either GPIB (IEEE 488.2) or front panel keypad.
  • Linear control for low noise: 100 micro-volts typical in voltage mode
  • High precision: 0.0005% source effect {regulation} in voltage mode.
  • Voltage and current control with equivalent performance.
  • High speed mode allows fast-recovery current-controlled stabilization into a varying load.
  • Overvoltage and overcurrent settings individually programmed by the front panel keypad or remotely by the bus with a programmable delay to allow for reactive-load transients.
  • Overvoltage crowbar to protect sensitive loads.
  • Non-volatile storage of programmed sequences or active settings.
  • Full talk-listen control from a GPIB (IEEE 488-2) using SCPI language.
  • Master-slave series and parallel operation to provide increased capability.
  • Local control: Front panel keypad entries are used for setting and adjusting the output. The keypad can be used to execute commands directly or to introduce a program to be run later or cycled.
Link to associated quotation page UL LISTED MARK CE Logo
KLN Series PhotoSERIES KLN Automatic crossover, low-profile, high-performance, low-cost, programmable, from 0 - 6V to 0 - 600V
  • Constant Voltage/Constant Current with automatic crossover
  • Switch mode topology for cool, efficient operation, speed control fan for low noise operation
  • RS 485 and isolated analog programming included on all models
  • Optional LAN interface (E suffix models)
  • Optional GPIB interface (G suffix models)
  • 1/2 rack, 1U panel height at 750 watts
  • Full rack, 1U panel height at 1500 watts
  • Full rack, 2U panel height at 3000 watts
  • Front to back air flow allows full power operation without spacers between supplies
  • Wide-range a-c input, 100-240V a-c, 50/60Hz with PFC
  • Up to 5 units in parallel and 2 units in series, equipped with active current sharing.
  • CE Mark approved.
  • Approved to LXI Version 1.4, Device Specification 2011
Link to associated quotation pageCE Logo
ATE Series Power Supplies with Analog and Digital MetersSERIES ATE Precision analog-controlled power supplies, 50 100, 250, 500, 1000 Watts, from 0 - 6V to 0 - 150V (325V for 250W model)
  • Linear programmable power in five sizes to 1000 watts.
  • Ultra low noise and ultra low ripple, high speed linear precision control.
  • Voltage and current stabilization, high gain and zeroable offsets
  • 10 turn panel controls offer exceptional resolution.
  • User-selectable capacitorless output for fast analog programming or quick recovery current-mode operation.
  • Optional Fast-mode for rapid response to programmed instructions or for quick response in current mode to load changes.
  • Full zeroing and full-scale calibration for both the voltage and current control channels.
  • Programmable overvoltage crowbar.
  • Uncommitted amplifiers to manipulate arbitrary control signals into the required 0-10V needed to program ATE. Two provided. Can be used for scaling and summing.
Link to associated quotation page UL LISTED MARK CE Logo
PRM Series Ferroresonant Power SuppliesSERIES PRM Modular ferroresonant voltage stabilizers with source-isolated, overload-protected output, 60W, 120W, 180W, 280W, 300W, 450W. 1 Output (fixed): 5/ 8/ 12/ 15/ 21/ 24/ 26/ 28/ 36/ 48/ 60/ 120/ 240V d-c.
  • Low cost, highly dependable
  • Extraordinary isolation from a wide variety of source noise.
  • D-c output is inherently short-circuit proof, cannot expose delicate loads to over-voltage hazards: no crowbar, fuses, or bounding circuits needed.
  • No noise-producing switches or oscillators.
  • Voltage setting is independent of delicate control settings or diode references, and requires no comparators, references, or limiters.
  • Efficiency is 65-75%.
  • Custom volt-ampere combinations, consult factory.
Link to associated quotation pageCE Logo
MST Series Power Supplies in RA 55 Rack AdapterSERIES MST High density voltage/current stabilizers, from 0 - 6V to 0 - 270V. Up to nine 200-watt plug-in power supplies in a 4U housing.
  • Switch-mode conversion, linear post regulator.
  • Wide range a-c input: 88-264V a-c with built-in power factor correction (PFC).
  • Forced current sharing for N+1 redundancy connection.
  • Series connection of 150V models allow output to 500V.
  • Polarity reversal relays provide 2-quadrant operation.
Link to associated quotation page CE Logo UL LISTED MARK

ProductsSupportLiteratureContact UsCareersAbout

TEL (718) 461-7000 • FAX (718) 767-1102 • email: